Material
Recyclable
Buy direct
Pegasus Sign Bollard
The Pegasus bollard is the ultimate sign carrying bollard for rectangular sign faces. With 305mm x 255mm signage capacity either side, the Pegasus is perfect for displaying disabled badge holder signs (661A) or enforcing other parking restrictions.
Use our Bollard Builder below to customise your bollard.
3.4m Speed Bump – Ready to Install
The 3.4m Speed bump is made up of 6 middle sections plus two end caps. These bumps are ideal for calming traffic especially around vulnerable road users such as near schools.
- Overall length is 3440mm with end caps, 50mm high.
- Made from a tough recycled thermoplastic material.
- Bolt down holes for 12mm bolts.
- A chequered pattern for extra grip.
- Fixings included.
Speed Bump End Caps (pair)
The speed bump end caps come in pairs and are fixed to the ends of the speed bump sections to leave a smooth finish to the speedbump.
These speed bumps are ideal for placing near areas that drivers need to reduce speed and take care.
- Made from a tough recycled thermoplastic
- Bolt down holes for easy installation
- A chequered pattern for extra grip
Munro Bollard
Bollard Conversion Plate
Our bollards can also be retrofitted to replace traditional base lit bollards, by using the Universal Conversion Plate, which allows easy installation without the need to excavate or remove the existing light box. The plates are manufactured from stainless steel and powder coated in matt black.
*Haldo variant available.
Corduroy Tactile Paving (10 tiles per box)
The Tactile Corduroy paving is very important to pedestrians negotiating our footpaths. The profile differs from the Blister profile to convey a different message: ‘hazard, proceed with caution’.
The Corduroy highlights the presence of specific hazards such as steps, level crossings or the approach to on-street rapid transit platforms (LRT). Comprising of rows of 6mm high rounded bars running transversely across the direction of the pedestrians travel.
Churchill Verge Marker Post
The Churchill bollard is a plastic blow moulded verge maker. Easy to install and hard wearing, the Churchill post has a cylindrical design with hi vis reflective area conforming to RI EN12899-1 class R2 reflectors.
- Multipurpose usage - highway verges / hard standing areas
- EN 12899-1 Class R2 reflectors.
EcoLight – Sign Light
Delivering industry-leading power efficiency, the EcoLight will illuminate traffic signs up to 1200mm and help you reduce carbon emissions on your network.
- Made from recycled material.
- Lightweight one-piece IP66 sealed sign light.
- Power consumption of only 2.6 watts
- 10 year warranty
Speed Bump Section – Yellow
City Post Hazard Marker
This TMP Verge Marker, is perfect for highlighting roadside verges and rebounding back to an upright position if hit.  It has been tested vigorously having endured 100 impacts at 100 kmh and still standing.
- Made of flexible polyurethane
- Remaining flexible at very high and low temperatures (-28°C to +75 °C)
- TSRGD compliant
- UV resistant
- 1 year limited warranty
- 360° visibility
No Entry – Car Park Sign Bollard
The TMP car park sign 'No Entry' is ideal for directing traffic into the correct path of flow, making it clear not to enter certain areas. With retro-reflective covering the sign can be seen perfectly in the low light of the car park making sure important information is always on hand.
- High-intensity Prismatic material 2-BS EN 12895-1:2001
- Reboundable
- Single Sided
- 3mm grey polypropylene
- Tested to withstand impacts at 60mph
Blister Tactile Paving (10 tiles per box)
The tactile Blister paving is essential to the safety of visually impaired people navigating our busy streets. This profile underfoot gives warning to the change of a footpath that meets a road, where there are no kerbs to differentiate the two. Comprising of rows of flat-topped 5mm high blisters. Also available as Corduroy.
The Buff coloured variant is used for where there are controlled crossing points, such as zebra, pelican and puffin crossings. The red variant is put in place where there are uncontrolled crossing points such as side road crossings, kerb to kerb flat road humps and busy cross overs
Chevron Right – Car Park Sign Bollard
The TMP car park sign 'Chevron Right' is ideal for directing traffic flow, and warning of tight corners. With retro-reflective covering the sign can be seen perfectly in the low light of the car park making sure important information is always on hand.
- High-intensity Prismatic material 2-BS EN 12895-1:2001
- Reboundable
- Single Sided
- 3mm grey polypropylene
- Tested to withstand impacts at 60mph
Short Tubular Hazard Marker
Munro Steel-Core Bollard
Blister Intermittent Glo Tactile Paving (10 tiles per box)
The tactile Blister paving is essential to the safety of visually impaired people navigating our busy streets. This profile underfoot gives warning to the change of a footpath that meets a road, where there are no kerbs to differentiate the two. Comprising of rows of flat-topped 5mm high blisters. Also available as Corduroy.
The Buff coloured variant is used for where there are controlled crossing points, such as zebra, pelican and puffin crossings. The red variant is put in place where there are uncontrolled crossing points such as side road crossings, kerb to kerb flat road humps and busy cross overs.
Corduroy Glo Tactile Paving (10 tiles per box)
The Tactile Corduroy paving is very important to pedestrians negotiating our footpaths. The profile differs from the Blister profile to convey a different message: ‘hazard, proceed with caution’.
The Corduroy highlights the presence of specific hazards such as steps, level crossings or the approach to on-street rapid transit platforms (LRT). Comprising of rows of 6mm high rounded bars running transversely across the direction of the pedestrians travel.
Blister Full Edge Glo Tactile Paving (10 tiles per box)
The tactile Blister paving is essential to the safety of visually impaired people navigating our busy streets. This profile underfoot gives warning to the change of a footpath that meets a road, where there are no kerbs to differentiate the two. Comprising of rows of flat-topped 5mm high blisters. Also available as Corduroy.
The Buff coloured variant is used for where there are controlled crossing points, such as zebra, pelican and puffin crossings. The red variant is put in place where there are uncontrolled crossing points such as side road crossings, kerb to kerb flat road humps and busy cross overs.
Manchester Bio Bollard
Evo-SightScreen
The Evo-SightScreen is a reboundable visibility screen designed to reduce the speed of vehicles on the approach to roundabouts. Completely modular, the Evo-SightScreen is built using the same components as the award-winning Evo-Chev and can be made to any length.
- Modular system
- Durable and economical
- Easy to install
- Recyclable
- BS EN 12767:2019 Passively Safe
Essex 76mm Ladder Bar Polymer Embellishment
Unlike traditional cast-iron or aluminium, our new non-metallic heritage lighting column embellishments do not need to be removed when testing the structural integrity of the column. This makes the process safer, quicker and cheaper!
- To fit 76mm dia. shaft columns
- Made from polymer and finished in Gloss Black
Essex 114mm Ring Polymer Embellishment
Unlike traditional cast-iron or aluminium, our new non-metallic heritage lighting column embellishments do not need to be removed when testing the structural integrity of the column. This makes the process safer, quicker and cheaper!
- To fit 114mm dia. shaft columns
- Made from polymer and finished in Gloss Black
Essex 89mm Ring Polymer Embellishment
Unlike traditional cast-iron or aluminium, our new non-metallic heritage lighting column embellishments do not need to be removed when testing the structural integrity of the column. This makes the process safer, quicker and cheaper!
- To fit 89mm dia. shaft columns
- Made from polymer and finished in Gloss Black
Essex 76mm Ring Polymer Embellishment
Unlike traditional cast-iron or aluminium, our new non-metallic heritage lighting column embellishments do not need to be removed when testing the structural integrity of the column. This makes the process safer, quicker and cheaper!
- To fit 76mm dia. shaft columns
- Made from polymer and finished in Gloss Black
